Luxwise › Lux Converter and Light Meter Calibration

Lux Converter and Light Meter Calibration

Convert lux to foot-candles, see how far a phone light reading can be off, work out a calibration from a reference meter, and estimate lux from your camera's exposure. A browser cannot read a light sensor, so to measure light you need the Luxwise app on Android. Free, no sign-up, the same numbers as the app.

Lux and foot-candles

Possible error of a phone reading—
The true light is likely within—

The band is the one Luxwise prints next to every reading: the larger of a floor (1 lx sensor, 3 lx camera) and the percentage, rounded up.

Measure, log and chart the light liveIn the Android app

Calibrate against a reference meter

Phone and reference meter side by side, in your usual light.

Calibration—
Corrected reading—
Unlimited calibration profiles (per phone and reference meter)Pro in the app

Lux from camera settings

Exposure value at ISO 100 (EV100)—
Estimated illuminance—

Use the settings your camera chose by itself (auto-exposure) for an evenly lit scene. It is an estimate, about ±40 %.

Typical reference values (EN 12464-1, as commonly cited)

Room or taskLuxFoot-candlesUniformity U₀
Office: writing, typing, reading500460.60
Meeting / conference room500460.60
Technical drawing750700.70
Classroom500460.60
Corridor, circulation area1009.30.40
Stairs150140.40
Toilets, washrooms200190.40
Shop sales area300280.40
Commercial kitchen500460.60
Store room, warehouse1009.30.40
Fine assembly work750700.70

Maintained illuminance on the task area. A guide for comparison, not a compliance test: the standard itself, and the task actually done in the room, decide.

Guided room-grid survey: average, minimum, U₀ and heat mapPro in the app
Luxwise Pro

Measuring a whole room?

The Luxwise app does everything on this page offline, and Pro adds the rest. One payment, no subscription.

  • Unlimited and all-day logging (screen off on Android)
  • CSV export with the calibration in the header
  • Guided room-grid survey: average, minimum, U₀ and heat map
  • PDF inspection report with your logo, notes and signature line
  • Unlimited calibration profiles (per phone and reference meter)
  • Plant mode: PPFD and DLI estimates for grow lights
  • No ads

Questions

How many lux is one foot-candle?

One foot-candle is one lumen per square foot, which is 10.764 lux. To turn lux into foot-candles, divide by 10.764; to turn foot-candles into lux, multiply by 10.764. 500 lux is about 46.5 foot-candles.

How accurate is a phone light meter?

Published comparisons against reference meters found uncalibrated phones reading about 28–38 % off on average, and about 8–10 % after calibration. Luxwise prints ±30 % next to an uncalibrated Android reading and ±10 % after calibration, rounded up. An iPhone estimates light from its camera, which is less accurate again (±40 %, or ±15 % calibrated).

How do I calibrate my phone's light meter?

Put the phone and a reference lux meter side by side in the same light and note both readings. With one point the factor is the meter's reading divided by the phone's. With two points — a dim light and one at least three times brighter — you also get an offset: lux = raw × factor + offset. The Luxwise app walks you through this and stores the result as a profile.

How much light does an office need?

EN 12464-1 is commonly cited at 500 lux maintained for writing, typing and reading, 100 lux for corridors and 750 lux for technical drawing. These values are a guide for comparison, not a compliance test: the standard itself, and the task actually done in the room, decide.

Can a website measure the light in my room?

No. A browser has no access to a phone's light sensor. This page only works with numbers you type. To measure, log and survey a room, use the Luxwise app on an Android phone, which reads the real light sensor.

How it is calculated

  • 1 foot-candle = 1 lumen per square foot = 10.763910416709722 lux. Readings below 10 are shown with one decimal, the rest as whole numbers.
  • ± band = the larger of a floor (1 lx for a light sensor, 3 lx for a camera estimate) and a share of the reading: 30 % uncalibrated, 10 % calibrated (Android light sensor); 40 % and 15 % (iPhone camera). Rounded up to 0.1 below 10, to 1 below 100, to 5 below 1000, to 10 above.
  • One-point calibration: factor = reference ÷ phone, offset 0. Two points: factor = (ref₂ − ref₁) ÷ (raw₂ − raw₁), offset = ref₁ − factor × raw₁. A factor outside 0.05–20, a negative factor or the same phone reading twice is refused. Corrected lux = raw × factor + offset, never below 0.
  • Camera estimate: EV100 = log₂(N² ÷ t) − log₂(ISO ÷ 100), and E = 2.5 × 2^EV100 lux (incident-light constant C = 250, ISO 2720).
  • Reference values: maintained illuminance and uniformity commonly cited from EN 12464-1:2021, the same list the Luxwise app uses.

The calculation runs in your browser; nothing you type is sent anywhere. It is the same engine as the Luxwise app.